by Staff Writers
Plymouth, UK (SPX) Oct 10, 2014
The human and environmental dangers posed by a widely used manufacturing technique could be almost eradicated thanks to research led by Plymouth University. Fibre-reinforced polymer matrix composites are employed in a vast array of industries, and are painted or sprayed onto products to provide a high-quality finish in transport applications, chemical plants, renewable energy systems and pipelines.
But that finishing process causes the vapours of a volatile organic compound - styrene, found in polyesters and vinyl-esters - to be emitted, posing potential health and wellbeing risks to the workforces involved and the wider environment.
Now a team from Plymouth University, part of the euro 1.4million InGeCt project funded by the European Union's Framework Programme 7 (FP7) initiative, has identified that in-mould gel-coating could reduce average styrene levels by more than 98 per cent and provide a route to improved workplace conditions and reduced environmental impact.
Dr John Summerscales, Associate Professor in Composites Engineering at Plymouth University, led the study. He said: "Styrene has been the subject of extensive debate in respect of health and environmental issues. Exposure to styrene has previously been linked to altered mood states, in particular aggression, while its vapour has been reported to cause depression, fatigue and a slowing in reaction times. By reducing styrene levels in the workplace, there would be numerous positive results such as improving retention of workforce personnel, minimising release to the environment and reducing odour at the factory boundary."
The European-wide study compared three techniques used in the finishing process - conventional hand-painted gel-coating, in-mould gel-coating with a separator fabric and in-mould surfacing with a silicone shim processes - to establish if styrene levels can be significantly reduced by the adoption of closed mould systems.
The hand-painted technology was found to have significantly higher levels of styrene emission than the two closed mould processes. For the open mould process, the average styrene levels were in the range 28-70 parts per million (ppm).
The two closed mould technologies were shown to significantly reduce the measured styrene levels, to lie in the range 0.23-0.37 ppm, demonstrating a reduction in average styrene emission levels of more than 98 per cent, with obvious benefits for worker health and the reduction of environmental burdens.
Dr Summerscales added: "The occupational exposure limits for styrene currently vary across the European Union, but a recent directive (REACH) is likely to result in the harmonisation of permitted styrene levels - most probably at the current lowest (Scandinavian) level. The recommendation for a 20ppm time-weighted average, which would be an 80 per cent cut in the UK, is unlikely to be achievable with open mould gel-coating. The research we have undertaken aims to keep composites manufacturing within the EU, rather than exporting difficult manufacturing processes to less regulated countries, with subsequent benefits for employment within European nations."
InGeCt was a two-year research collaboration, whose main aim is to develop an innovative environmentally friendly gel-coating technology for composites for marine and wind-turbine applications to reduce VOC emissions, processing time and cost.
Led by Plymouth University, it also involved academics and companies across Europe including Alan Harper Composites (Cornwall, UK), Centro Tessile Cotoniero E Abbigliamento SpA (Italy), De IJssel Coatings BV (Netherlands), KMT Nord APS (Denmark), Lightweight Structures BV (Netherlands), SP Technical Research Institute of Sweden (Sweden),Tessitura Valdolona SRL (Italy).
Space Technology News - Applications and Research
|The content herein, unless otherwise known to be public domain, are Copyright 1995-2014 - Space Media Network. All websites are published in Australia and are solely subject to Australian law and governed by Fair Use principals for news reporting and research purposes. AFP, UPI and IANS news wire stories are copyright Agence France-Presse, United Press International and Indo-Asia News Service. ESA news reports are copyright European Space Agency. All NASA sourced material is public domain. Additional copyrights may apply in whole or part to other bona fide parties. Advertising does not imply endorsement, agreement or approval of any opinions, statements or information provided by Space Media Network on any Web page published or hosted by Space Media Network. Privacy Statement All images and articles appearing on Space Media Network have been edited or digitally altered in some way. Any requests to remove copyright material will be acted upon in a timely and appropriate manner. Any attempt to extort money from Space Media Network will be ignored and reported to Australian Law Enforcement Agencies as a potential case of financial fraud involving the use of a telephonic carriage device or postal service.|